What models of Haishi injection moulding machines are available?

News source:Haishi plastic machine Time:2015-02-02
The working principle of the injection molding machine is similar to that of the syringe used for injection, it is with the help of the screw (or plunger) thrust, the molten state has been plasticized well

Vertical injection moulding machine (i.e. viscous flow state) of the plastic injection into the closed cavity, after curing the shape of the product to obtain the process.

Injection moulding is a cyclic process, each cycle mainly includes: dosing - melt plasticisation - pressure injection - mould filling and cooling - mould opening and removal. After taking out the parts, the mould is closed again for the next cycle.

Injection moulding machine operation items: The injection moulding machine operation items include the operation of the control keyboard, the operation of the electrical control system and the operation of the hydraulic system. The injection process action, filling action, injection pressure, injection speed, ejector type selection, barrel temperature monitoring of each section, injection pressure and back pressure adjustment, etc.

The molding process of the general screw injection molding machine is: first of all, the granular or powdered plastic is added to the barrel, and the plastic becomes molten through the rotation of the screw and the heating of the outer wall of the barrel, then the machine is closed and the injection seat is moved forward, so that the nozzle is close to the gate channel of the mould, then the injection cylinder is fed with pressure oil, so that the screw is pushed forward, thus injecting the molten material into the lower temperature with high pressure and fast speed. After a certain period of time and pressure maintenance (also known as pressure-holding), cooling, so that it is cured, you can open the mold to take out the product (the purpose of pressure-holding is to prevent the backflow of molten material in the mold cavity, to replenish the material in the mold cavity, as well as to protect the general horizontal injection molding machine certificate products with a certain density and size tolerance). The basic requirements of injection moulding are plasticisation, injection and moulding. Plasticisation is a prerequisite for achieving and ensuring the quality of the moulded product, while injection must ensure sufficient pressure and speed in order to meet the requirements of moulding. At the same time, due to the high injection pressure, a correspondingly high pressure is generated in the mould cavity (the average pressure in the mould cavity is generally between 20 and 45 MPa) and therefore a sufficiently large clamping force must be available. It follows that the injection unit and the mould closing unit are the key components of the injection moulding machine.

There are three main aspects to the evaluation of plastic products. The first is the quality of appearance, including integrity, colour, lustre, etc.; the second is the accuracy between dimensions and relative positions; and the third is the physical, chemical and electrical properties corresponding to the application. These quality requirements, in turn, vary according to the scale required for the use of the product. Defects in the product are mainly in the design of the mould, the accuracy of manufacture and the degree of wear and tear. However, the fact is that technicians in plastics processing plants are often faced with the difficult situation of using technology to remedy the problems caused by mould defects with little success.

The adjustment of the process during production is a necessary way to improve the quality and yield of the product. As the injection moulding cycle itself is very short, if the process conditions are not well mastered, scrap will continue to flow. When adjusting the process, it is best to change only one condition at a time and observe a few times, if the pressure, temperature and time are adjusted together, it is easy to cause confusion and misunderstanding, and it is not clear what the reason is when problems occur. There are many ways to adjust the process. For example, there are more than ten possible ways to solve the problem of insufficient product injection, and to choose one or two main solutions to the problem in order to really solve the problem. In addition, attention should be paid to the discriminatory relationship in the solution. For example, if the product is sunken, sometimes the material temperature should be increased, sometimes it should be decreased; sometimes the material quantity should be increased, sometimes it should be decreased. It is important to recognise the feasibility of reverse measures to solve the problem.
Business cooperation, please contact us

Enhance the core competitiveness of customers Create higher value for customers

Consult Now